How Do You Bypass the Wattage Governor on a Ceiling Fan Light

I’m going to show you how to bypass the wattage governor on a ceiling fan light. The process is pretty simple, but you must have a basic understanding of electricity and wiring before attempting this project. If not, don’t do this! You might get electrocuted, or something else bad could happen. But if you’re an electrician looking for some side work, keep reading.

How Do You Bypass the Wattage Governor on a Ceiling Fan Light

Let me start by saying that I am not responsible for any damages resulting from your attempts at following these steps. It’s always best to consult with an electrical contractor to make sure everyone involved is safe and gets what they want out of the project, especially when dealing with electricity. This blog post will show you how do you bypass the wattage governor on a ceiling fan light.

Step to Follow on How Do You Bypass the Wattage Governor on a Ceiling Fan Light

Step One: Open the Cover of Your Ceiling Fan

First, you will need to locate your ceiling fan. If you are unsure where it is located in your home, follow any cords coming from the wall until you find it. Make sure that all power has been turned off before opening up the cover over your lighting fixture. The cover must be mounted with screws.

Open the Cover of Your Ceiling Fan

If you find that your light fixture is attached with only a couple of clips, then it will not be possible to bypass the wattage governor on your ceiling fan light. You will need a Phillips head screwdriver to remove screws from the light cover. Take your time and be very careful when removing them, so you do not damage any surrounding areas or cause injury to yourself.

Step Two: Getting to the Wiring

Once you have removed the cover, you will need to find the wire attached to or leading into your light fixture. You will see that there are two wires attached to the wattage governor. It should be fairly easy for you to distinguish between them because one of them has a larger prong than the other. The larger prong is the hot wire, and the smaller prong is the neutral wire.

If you have no idea which one should be hot and which one should be neutral, it would be best to label them with masking tape and a marker before touching anything. You can also choose to use an ohmmeter or a voltage tester to determine the hot and neutral wires. These can be purchased precut for a very low price at any hardware store.

Step Three: Loosening the Wires from the Governor

Once you have located your hot wire, twist it with your hand until it is about to come out of the terminal on your light fixture. You will then need to loosen the screw on this wire. Please do not eradicate it. Allow some room for movement of the wire to prevent fraying or damage that may occur if too much tension is applied to your wires.

Then, locate your neutral wire. You will need to follow the same procedure as above. If you are having trouble loosening up these wires, try turning the screwdriver horizontally so that it can no longer turn. If this fails, then apply some lubricant to loosen the screws up. You should then be able to twist the wires out of their housing.

Step Four: Removing the Governor

You will need to remove the old wattage governor. This is the metal box surrounding the wires where they are connected to your light fixture. Gently pull it away from your fan so that it comes free. It should be fairly easy to remove, but you may have to give some assistance by using a screwdriver for leverage.

Once you have removed your governor, you can then take it to an authorized dealer and ask them for assistance in properly disposing of it. They will usually charge a fee for this service, but it is worth it to keep their business thriving. You can also choose to solder or use electrical tape to seal the gap left behind by the governor.

Step Five: Make the Wire Connections

You will need to strip the insulation off of each wire. You can do this by using either a pair of scissors or wire strippers. First, cut about an inch off to have enough bare wire exposed to solder onto your fan wires. Once you have stripped both your hot and neutral wires, you can twist them around the fan wires.

If they cannot fit together due to insulation, then trim them with your wire strippers so that they can touch each other. Once all of your wires are connected, place the old wattage governor into the trash and find a suitable replacement for it at your local hardware or appliance store. This will help in how do you bypass the wattage governor on a ceiling fan light.

Step Six: Replacing the Light Cover

After you have replaced your wattage governor with a new one, you can replace the light cover and screw it back in place. If you had to solder or tape any exposed wiring, be sure to wait for it to cool down before attempting this step. You could also choose to replace both screws, no matter if the wiring is soldered or not.

Replacing the Light Cover

Reassemble your ceiling fan in the reverse order you took it apart. This will complete your installation of a wattage governor on your ceiling fan light. Now you can enjoy this newly adjusted lighting in your home or office without worrying about excessive power usage. The article has been a good guide on how do you bypass the wattage governor on a ceiling fan light.

Frequently Asked Question

What Is the Maximum Wattage for a Ceiling Fan Light?

The maximum wattage for a ceiling fan light is usually around 200 watts. However, it depends on the size of the fan as well as its location in your home.

Why Does My Ceiling Fan Light Turn on and Off by Itself?

One of the most common problems that people encounter with their ceiling fan is when it turns on and off by itself. This is a very common problem, and there are many possible causes for this.

Some of the more common causes for your ceiling fan turning on and off by itself are:

  1. A loose wire or connector at the electrical box where the power cord enters your home.
  2. A tripped circuit breaker in your electrical panel that may have been caused by a blown a fuse or circuit breaker in your home’s main panel (this should be replaced).
  3. The motor controller board inside your ceiling fan has gone wrong, which can happen due to overheating, arcing, moisture, too much current drawn from the power supply, or other factors related to electronic components that cause them to fail over time.

What Wattage Is Best for Ceiling Fan?

There are many types of ceiling fans available in the market that have different wattages and some with more advanced features.

The most common type of fan is a standard 12-volt, 60-watt or less, 3-speed ceiling fan. This fan provides cool air during the summer and can be used in conjunction with an AC unit when it gets cold outside. The most popular brand for these fans is Hunter because they offer a wide variety of colors and sizes as well as simple controls that make them easy to use.

A higher wattage, such as a 20-watt or 40-watt, has three speeds with no speed settings, but it may be easier to find a suitable replacement light bulb than on a lower wattage ceiling fan.

How Many Watts Does a Fan Light Use?

Watts is a measure of power consumed by an electrical device or appliance. It is measured in units called watts (W). A watt is equal to one joule per second. One watt can light up a 100-watt light bulb for one hour, which is about 3200 seconds.

Conclusion

If you have a ceiling fan with a light, but the wattage governor prevents it from being bright enough, here’s what to do. First of all, make sure that your circuit breaker is on and not tripped. Then turn off your power switch for the house or apartment.

Finally, locate where you want to bypass the wattage governor by locating three wires in white insulation, one black wire and two whites going up into the socket area inside the fan housing box near where they connect to each other at the top-rear corner of this section of wiring should be insulated with an additional strand or two running down below them.

Check it Out – How to Run a Fan Without Electricity

Smart Home Pick
Logo