How to Bypass Dryer Door Switch

76 0

Most people know they need to bypass the door switch on their clothes dryer when changing the belt. But did you know there is an easy way to do it? The door switch is likely located on the front panel if you have a front-loading clothes dryer. This switch allows you to start or stop the dryer by opening and closing the door.

If your dryer isn’t working, it’s possible that the switch has gone bad and needs to be replaced.

In this article, we’ll show you how to bypass dryer door switch so that you can test whether or not it’s causing your problem. Keep in mind that this should only be done as a temporary measure and that the switch should be replaced as soon as possible. Let’s get started!

Is It Possible to Bypass the Dryer Door Switch?

Yes, it is possible to bypass the dryer door switch. However, we only recommend doing this as a temporary measure. This is because the door switch is there for a reason – to keep the dryer from running when the door is open.

If you bypass the door switch, you’re essentially removing a safety feature from your dryer. So, while it may allow you to test whether or not the switch is causing your problem, it’s not something that should be done permanently. That said, let’s look at how to easily bypass the dryer door switch.

10 Steps on How to Bypass Dryer Door Switch

1. Locate the Door Switch:

The first step is to locate the door switch. On most dryers, this switch will be located on the front panel. Make sure that the dryer is unplugged before proceeding. If the dryer is plugged in, there is a risk of electrical shock.

2. Remove the Front Panel:

Once you’ve located the door switch, the next step is to remove the front panel. This will vary depending on your dryer model, so consult your owner’s manual for specific instructions. You can remove front panels by removing screws or snapping them off.

3. Disconnect the Wires from the Door Switch:

Once you have access to the door switch, you’ll need to disconnect the wires. Two wires will be connected to the switch – one black and one white. Use a pair of needle-nose pliers to remove the wires carefully.

4. Connect the Wires Together:

Now, take the black wire and connect it to the white wire. You can use a twist-on connector or solder the connection. Just make sure that the connection is secure. If you are using a solder connection, make sure to use heat shrink tubing to insulate the connection.

Now, take the other end of the black wire and connect it to one of the terminals on the door switch. Make sure that the connection is secure.

Finally, take the other end of the white wire and connect it to the other terminal on the door switch. Make sure that this connection is also secure.

5. Test the Connection:

Now, it’s time to test the connection. Close the dryer door and make sure that the door switch is engaged. You should hear a click when you close the door. The connection is not secure if you don’t hear a click.

Once you’ve verified that the door switch is engaged, turn on the dryer and let it run for a few minutes. If everything works properly, you’ve successfully bypassed the door switch.

6. Replace the Front Panel:

Now that you’ve successfully bypassed the door switch, it’s time to replace the front panel. This is simply a reversal of the process you used to remove the panel. Make sure that all of the screws are tight and that the panel is securely in place.

7. Test the Dryer Again:

Make sure to reconnect the dryer vent and turn on the gas before testing your newly bypassed dryer door switch. If everything is working properly, your dryer should start up without any issues. If you are still having problems, you may need to check other dryer components for damage.

8. Reconnect the Wires to the Door Switch:

This is the most difficult part of the process. You will need to reconnect the wires to the door switch. The best way to do this is to use a multimeter. You can use a continuity tester if you do not have a multimeter.

First, disconnect the power to the dryer. Then, remove the screws that hold the door switch in place. Next, disconnect the wires from the door switch.

Now, you will need to connect the wires to the new door switch. The best way to do this is to use a multimeter. You can use a continuity tester if you do not have a multimeter.

9. Replace the Front Panel:

Now, it’s time to replace the front panel. This is simply a reversal of the process you used to remove the panel. Make sure that all of the screws are tight and that the panel is securely in place.

10 . Check the Door Switch:

Finally, it’s time to check the door switch. Close the dryer door and make sure that the door switch is engaged. Then, turn on the dryer and let it run for a few minutes. If everything works properly, you’ve successfully bypassed the door switch.

If your dryer doesn’t seem to be working properly after bypassing the door switch, there may be another issue. Consult your owner’s manual or call a qualified repair person for assistance.

Following these simple steps can easily bypass a dryer door switch. Just remember to unplug the dryer before beginning any work and to double-check all of the connections before turning on the dryer. With a little bit of care, you can easily bypass a dryer door switch and get your dryer up and running again.

Additional Tips and Tricks

You can use a clothespin or a paper clip to bypass the dryer door switch.
If your dryer has a lint trap, you can try cleaning it out to see if that helps the dryer work better.
You can also try opening up the dryer and looking at the door switch to see if there is anything that could be blocking it from working properly.
If all else fails, you can always call a professional to help you troubleshoot your dryer’s door switch.
If your dryer is still not working after trying all of these tips, it may be time to replace the door switch.

These tips may help you if your dryer is not working.

Necessary Precautions You Need to be Taken

Always unplug your dryer from the wall outlet before beginning any work on it.
Be sure to wear gloves and eye protection while working on your dryer.
Make sure that the area around your dryer is well-ventilated.
You need to be familiar with the different parts of your dryer before beginning this project.
Always consult your dryer’s owner’s manual for instructions specific to your model.

What Should You Do If the Dryer Switch Board Is Broken?

If the dryer switchboard is broken, you will need to replace it. You can purchase a new switchboard from your local appliance store or online. Be sure to get the correct model number for your dryer. Once you have the new switchboard, follow your owner’s manual instructions to install it.

Can a Dryer Work Without Board Switch?

A dryer can work without a board switch, but it will not be as safe. The board switch prevents the dryer from starting if the door is open. Without the switch, the dryer could start even if the door is open, which could be dangerous.

It is best to replace the board switch if it is broken. You can purchase a new switch from your local appliance store or online. Be sure to get the correct model number for your dryer. Once you have the new switch, follow your owner’s manual instructions to install it.

Conclusion

A dryer door switch is a vital part of your dryer. It helps keep the dryer running safely by preventing it from turning on when the door opens. If your dryer door switch is broken, you can easily bypass it. Just remember to unplug the dryer before beginning any work and double-check the connections before turning on the dryer.

Bypassing the switch is a simple process that can be done in just a few minutes. With this knowledge, you can fix your broken dryer without spending any money on repairs. Hopefully, this guide could help you know how to bypass dryer door switch.

Have you ever had to bypass your dryer door switch? What was the process like for you? If you have any questions or comments, please feel free to leave them below. Thanks for reading!

You Can Chack It Out Shorten Cabinet Knob Screw