How to Bypass Lid Switch on Kenmore Washer

Are you having trouble getting your Kenmore washer to start? It may be because the lid switch is faulty.

If you are like me, you have probably, at some point, had to deal with the dreaded lid switch on your Kenmore washer. This little piece of hardware can oftentimes be the source of much frustration. You have probably had to go through the hassle of unplugging your Kenmore washer in order to bypass the lid switch. Well, there is a better way! 

In this blog post, I am going to show you how to bypass lid switch on kenmore washer, so that you can get your laundry done without having to worry about it. Enjoy!

How to Bypass Lid Switch on Kenmore Washer

Is It Possible to Bypass the Lid Switch on Kenmore Washer?

The lid switch on a Kenmore washer is located on the top of the washer, near the lid. It is a small piece of hardware that is used to sense whether or not the lid is closed. If the lid switch is faulty, it can prevent the washer from starting.

Fortunately, it is possible to bypass the lid switch on a Kenmore washer. Bypassing the lid switch is a simple process, and it only takes a few minutes.

Does It Seem Difficult?

Bypassing the lid switch on a Kenmore washer may seem complicated, but it is pretty easy to do. All you need is a screwdriver and a pair of pliers. I will show you how to do it step by step so that you can get your laundry done in no time.

10 Steps on How to Bypass Lid Switch on Kenmore Washer

1. Unplug the Washer:

This is an important safety step. You don’t want to be electrocuted while you are working on your washer. First, you need to unplug the power cord from the outlet. Then you need to find the wiring diagram for your washer. The wiring diagram is usually located inside the control panel. Once you have found the wiring diagram, locate the wire that goes to the lid switch and disconnect it.

Unplug the Power Cord From the Outlet

2. Remove the Top Panel:

The next step is to remove the top panel of your washer. This will give you access to the lid switch. To remove the top panel, first, you need to remove the screws that are holding it in place. There are usually two or three screws. Once you have removed the screws, lift the top panel off of the washer.

3. Locate the Lid Switch:

The lid switch is located on the top of the washer, near the lid. It is a small piece of hardware that is used to sense whether or not the lid is closed. Be careful not to damage the lid switch as you remove it.

4. Remove the Lid Switch:

Now that you have located the lid switch, it is time to remove it. To do this, you need to disconnect the two wires that are connected to it. Once done, you can remove the lid switch from the washer.

Located the Lid Switch

5. Bypass the Lid Switch:

The next step is to bypass the lid switch. To do this, you need to take a screwdriver and connect the two wires that you disconnected in the previous step. When the washer turns on, you will know that you have done this correctly.

6. Reconnect the Wire:

Once you bypass the lid switch, you need to reconnect the wire you disconnected in step one. This will ensure that your washer is getting power. Make sure that you connect the wire to the correct terminal. If you connect to the wrong terminal, your washer will not work.

7. Put the Top Panel Back on:

Now that you have bypassed the lid switch, it is time to put the top panel back on. First, ensure that the wire you reconnected in step six is not in the way. Then, replace the screws that you removed in step two.

8. Test the Washer:

Now that you have bypassed the lid switch, it is time to test your washer. Ensure the water is turned on and the power cord is plugged into the outlet. Then, try to start your washer. It should start without any problems.

Test Your Washer

9. Turn Off the Washer:

Once you have tested your washer and it is working, you need to turn it off. To do this, simply unplug the power cord from the outlet. This step is important because you don’t want to forget to turn off your washer and run it all day.

10. Put the Lid on the Washer:

Now that your washing machine lid switch is bypassed, you can put the lid back on the washer. Ensure the lid is properly in place and screwed down before starting a load of laundry. If the lid is not properly in place, the washing machine may not operate correctly.

It is important to note that some newer model washing machines will not operate without the lid in place. If your washing machine is one of these models, you will need to leave the lid off while a load of laundry is washing.

By Following these simple steps, you can easily bypass the lid switch on your Kenmore washing machine. This will allow you to use your washing machine even if the lid switch is broken. However, it is important to note that bypassing the lid switch may void your warranty. Be sure to check your warranty before bypassing the lid switch on your Kenmore washing machine.

You Can Put the Lid Back on the Washer

Additional Tips and Tricks:

  1. You can also bypass the lid switch by jumpering across the two terminals on the switch. This can be done with a paperclip or a small piece of wire.
  2. If your washer does not have a lid switch, you can still bypass it by disconnecting the power to the washer and then opening up the control panel. Once you have access to the control panel, you can simply disconnect the wire that goes to the lid switch.
  3. If you have a front load washer, you can bypass the lid switch by opening up the door and disconnecting the door switch. This will allow you to start the washer without using the lid switch.
  4. You can bypass the lid switch by disconnecting the power to the washer and opening the control panel. Once you have access to the control panel, you can simply disconnect the wire that goes to the lid switch.
  5. If you have a front load washer, you can bypass the lid switch by opening up the door and disconnecting the door switch. This will allow you to start the washer without using the lid switch.

With these tips, you should be able to bypass the lid switch on your Kenmore washer without any problems. If you have any other questions or need more help, feel free to ask us in the comment section below. Thanks for reading!

Precaution You Need to Be Taken

  1. You need to put the washer into a diagnostic mode in order to bypass the lid switch.
  2. Ensure you have unplugged the washing machine before working on it.
  3. You should wear rubber gloves while you are working on the washer lid switch.
  4. Be very careful while bypassing the lid switch, as it can be dangerous.
  5. Make sure to follow the instructions carefully.

Taking precautions is necessary to avoid any electrical shock. Follow the above tips, and you can bypass the lid switch on your Kenmore washer without any problems. Thanks for reading!

Can the Washer Work Without a Lid Switch?

Yes, a washing machine can work without a lid switch. However, it is important to note that bypassing the lid switch may void your warranty. Be sure to check your warranty before bypassing the lid switch on your Kenmore washing machine. Otherwise, you may be risking electrical shock or damage to your machine.

How Can You Recognize a Bad Lid Switch?

There are a few symptoms that can indicate a bad lid switch. If your washing machine doesn’t start when you close the lid, or if it starts and then stops immediately, this could be a sign of a bad lid switch. Additionally, if your washing machine is making strange noises or seems to be operating inconsistently, this could also indicate a problem with the lid switch. If you notice any of these symptoms, it’s important to check the lid switch for damage and replace it if necessary. Thanks for reading!

Conclusion

Although this blog post has detailed how to bypass lid switch on kenmore washer, it is important to note that doing so can be dangerous. If you choose to follow these instructions, please do so at your own risk.

Additionally, we recommend that you only use this method as a last resort and reach out to a professional if you cannot fix the issue yourself.

Hopefully, our guide has given you the information you need to get your washing machine up and running again. Have you tried any of the methods we’ve suggested? Let us know in the comments below!

You Can Chack It Out How to Bypass Thermal Switch on Water Heater

Smart Home Pick
Logo