How to Cut Hole in Mirror for Outlet

Mirrors are not just for admiring your reflection. You can use them to break up a wall, make an otherwise boring room more interesting, or they can be used as a way to hide something you don’t want people seeing.

How to Cut Hole in Mirror for Outlet

One of the most popular uses for mirrors is adding light into dark areas. For example, if you have an outlet that’s hard to see in your bathroom but there’s no other place it could go, cutting a hole in the mirror near the outlet will provide ambient lighting and make it easier to plug things in.

It’ll also keep cords out of sight, which helps prevent tripping hazards! So, this article is for you. You will learn how to cut hole in mirror for outlet with just one simple trick!

Step to Follow on How to Cut Hole in Mirror for Outlet

Step One: Determine the Location of The Outlet.

Once you have determined where you would like to install your new receptacle, it is time to measure the distance between the studs behind where you want your mirror. Measure twice here to make sure that everything lines up correctly after cutting the first hole.

Determine the Location

Make sure to take the width of the outlet cover plate into account before making your final measurement. If you don’t, the power receptacle may not fit properly, or you may have to adjust your installation location.

Step Two: Cut Out a Circle in the Back of your Mirror

Use a Dremel rotary tool to cut out a hole in the back of the mirror. It only needs to be big enough for you to slide your new outlet and cover plate through. If you plan on using wall anchors, it is best not to make the hole too close to the edges or corners of the mirror, as most anchors require a screw to be inserted at least partially into the wall.

Make sure to wear safety glasses and earplugs when using a Dremel rotary tool, as bits can break apart and release shrapnel that can cause damage if it flies into your eye. You will also need a Dremel cutting wheel to cut the mirror, a sanding drum to level out the edges, and a high-speed cutter bit if you plan on using an adhesive such as silicone or liquid nails.

Step Three: Install Drywall Anchors for Mirror Installation

Once you have determined where your power source is located, it is time to attach your drywall anchors to install your mirror. Again, keep your mirror from cracking; it is best to use at least four anchors spaced equally around the back of the mirror. The number and placement of screws will depend on how sturdy you want your installation.

Install Drywall Anchors

Screw through the drywall into the studs behind, and then attach your mirror to those screws using mounting brackets to ensure your mirror stays securely in place. I recommend using what is referred to as “drywall screws” because they are smaller than regular screws and come with a drill bit that allows you to predrill the holes before driving them into the wall.

Step Four: Prepare the Outlet for Installation

Peel back the plastic cover on your power outlet and take off one of the side screws; this is only important if you use a metal box. Wrap both of the exposed wires with electrical tape to prevent them from touching anything once you begin to install your new receptacle.

This will help prevent fires and other accidents from occurring. Once you have prepared your power outlet for installation, slide it through the hole in the mirror and secure it with a metal strap if necessary. You can also attach a new cover plate at this time. A new double faceplate will conceal the unsightly drywall anchors behind the mirror.

Step Five: Test Your New Outlet

Plug in a lamp or other small appliance and check to see that it works before turning the power off. If everything is working, turn your power back on and screw in any screws that may have been pulled loose after plugging in the cord from your new receptacle.

Once you have tested your outlet, you can hang up your mirror and admire the new look. Remember that you should never install any outlet without first checking to ensure it is getting power. These steps should help you in learning how to cut hole in mirror for outlet.

Step Six: Clean Up

Once you have completed your project, make sure to clean up any debris or dirt that has gotten all over your mirror. If you used a Dremel rotary tool, it is probably best not to use one on this mirror for a while, as it can cause small bits of metal from the cutting wheel to get embedded into the surface.

If you do not want to use your mirror for a while, it is best to place some cardboard behind the outlet and cover all of the screw holes with duct tape so that there is no chance of light being visible through the wall. If you want to use the mirror immediately, some people like to place a piece of tissue paper behind the outlet and then reapply their mirror.

Step Seven: Enjoy Your New Outlet Mirror

Now that you have your outlet mirror installed, you can enjoy the convenience of never having to search for an outlet as you walk into a room. You also give your home a great cosmetic touch and save time so that you do not need to unplug anything to plug something new in.

Enjoy Your New Mirror!

This project is a great way to save time and money by installing a new outlet without hiring a professional electrician. Just make sure not to overload it because you never know what may happen if your mirror shorts out. It would not be enjoyable if that happened during a significant event or party.

You Can Check It Out to: Drill a Hole in a Mirror

Frequently Asked Question

Can You Cut a Mirror With Glass Cutter?

You cannot cut a mirror with a glass cutter. The cutter will not be able to get through the glass because it is too thick. You can use other types of cutting tools such as diamond saws or diamond bits to cut mirrors.

Can I Drill a Hole Above an Outlet?

Drilling a hole above an outlet is not recommended. If you are looking to replace the current outlet with a new one, it would be best to remove the old one and install the new one.

Is It Safe to Put Tape Over Outlets?

There are some instances where it is not recommended to use tape over outlets. If you have an outlet that has a high wattage, it is best to not cover the outlet with tape because this can cause an electrical shock or fire hazard.

For low-wattage outlets, taping them up would prevent water from getting into the outlet and destroying your equipment.


This blog post has given you a couple of easy and practical ways to cut a hole in your mirror for an outlet. If the task is daunting, we recommend using one of these methods to save time and money.

It may take some trial-and-error before finding the right size drill bit or jigsaw blade that works best with your mirror. Keep trying until you find what works! So, this article is for you. You will learn how to cut hole in mirror for outlet with just one simple trick!

Smart Home Pick