How to Fix Loose Carpet on Stairs

Carpet on stairs is a tricky thing. It can be difficult to maneuver up and down the steps without catching the edge of your shoe, or it could be loose due to wear and tear. If you are looking for how to fix loose carpet on stairs, then this blog post may provide some insight.

You want to find out how thick it is to know if you will need more than one layer of padding underneath it before installing new carpeting over top of it. The second step would be removing all furniture from the room above where the installation will take place so that there is no chance for anything falling through onto the carpeting.

How to Fix Loose Carpet on Stairs

If you’ve already removed the furniture and find that there is no pad left under your carpet, then you’ll want to install a new one before doing anything else.

7 Steps to Follow on how to fix loose carpet on stairs

Step One: Know the Reason

The first step to fixing loose carpet on stairs is to know why it’s happening in the first place. The primary reason for loose carpet on your stairs is because of the people walking up and down them every day. It usually happens to stairs that do not have any railing or rail to support the people’s weight using them.

Once the carpet begins to separate and loosen up on the stair tread, it will bring along with it some of the underlayment and sometimes even a little of the stair risers as well. It does this because it was not properly secured in the first place by the adhesive and maybe even staples.

Step Two: Identifying Damage to Stair Tread or Riser

When you begin to see the loose carpet on the stairs, there is already some damage to the stair tread or riser. These areas of damage are usually a result of a rip in the carpet from people stepping on it, especially if they have high heels.

Identify the Damage of Stair

A tear in the carpet fibers will be one of the most common reasons you will see the loose carpet on stairs that have been damaged this way. There are undoubtedly other times that you will see this, but the most common is when the stairs have no railing for support.

Step Three: Taking Up the Loose Carpet

When you have identified that your stairs have a tear in them, then it should be relatively easy to take up loose carpet on stairs. You need to get out your hand-held staple gun and put down some staples to secure the loose carpet back in place.

You can also use a paintbrush and glue to apply a layer of adhesive to the bottom and edges of the carpet and then press it back in place. The treads and risers will need to be cleaned with acetone, wax remover, or other solvents before you begin working on putting them back together again.

Step Four: Sanding Off Any Excess Carpet Overhang

Once you have re-secured the loose carpet on your stairs, you will need to sand off any excess of it hanging over the front of the tread or riser. Again, you can use an oscillating multi-tool with a sanding accessory on it, but this is probably best done by hand at first.

Sanding Off Any Excess Carpet Overhang

You will want to sand off enough of the excess carpet so that it is even with or slightly above the edge of the tread or riser that you are working on. You will then need to re-apply some adhesive and put some more staples in place just like before.

Step Five: Cleaning up Loose Carpet Bits

After you have finished putting the loose carpet back on the stairs, you will need to clean up all of the bits and pieces hanging off the edges. If there is any adhesive left behind or on top of the stairs, then it can be removed with acetone or some other solvent.

You might also need to sand down the top of the stairs a little bit again if you removed too much adhesive in your cleanup process. The last thing that you will need to do is put down some new carpet protection to help prevent future damage from happening to your stair treads and risers.

Step Six: Replace Loose Carpet on Stairs

The last thing that you will need to do is replace the loose carpet on your stairs. This will be done by using a staple gun and applying staples to either side of the loose cut end of the carpet. You can then re-stretch out the carpet tautly across your stair treads or risers and cut off the excess foam along the walls.

Replacing Loose Carpet Using Staple Gun

The last thing that you will need to do is vacuum up any excess carpet fibers and spray the whole area down with a carpet protectant to prevent future damage from happening to your stairs. If you want to learn more about how to fix loose carpet on stairs, keep reading.

Step Seven: Enjoy Your Newly Restored Carpet on Stairs!

Once you have finished putting the loose carpet back on your stairs, then you should enjoy having your newly restored carpet on the stairs. But, of course, the last thing you will want to do is put some railing back up so people can walk up and down them once more.

You might even find that this is a quick and easy way to put the loose carpet back on the stairs instead of replacing it entirely. However, if you choose to replace it, you will need to remove the damaged carpet and padding before putting down your new carpet.

You Can Check It Out to: Fix Carpet Tacks Poking Up

Conclusion

If you are looking for a quick fix to your loose carpet on the stairs, try double-sided tape. Cut it into strips and place them between the top of each stair, with one end overhanging onto the next step down.

The adhesive will hold up all day long without leaving any residue or damaging surfaces below. You can find this type of tape at most hardware stores. The conclusion paragraph is informative and provides information on how to fix loose carpet on stairs.

You may also like- How to Install Waterfall Carpet on Stairs

Smart Home Pick
Logo