How to Get Straightener Burns Out of Carpet

If you have a carpeted floor in your home, the chances are that it will get dirty. Whether it’s from kids spilling juice or pets leaving their mark on the floor, stains and dirt can become a big problem over time. One of the most common problems people run into with carpets is scorch marks caused by hair straighteners.

Straightener Burn Carpet

Scorching spots in the carpet can be unsightly and difficult to remove, so here are some tips for getting that burn marks out of your rug! So, this article is for you. You will learn how to get straightener burns out of carpet with just one simple trick!

Step to Follow on How to Get Straightener Burns Out of Carpet

Step One: Locate the Burn

The first step to take when you have burned carpet is to find the exact spot. Then, sprinkle a little water on the carpet and wait about five minutes until you see where the burn has discolored it. The area will be very noticeable because it will not match the surrounding area in color or texture.

Locate the Burn

If you are unable to see it right away, you may need to pull back the carpet. Then, remove the baseboards so that you can lift the carpet without tearing it. Once you find the burn, mark it with a pencil or piece of chalk so that you know where to concentrate your efforts.

Step Two: Vacuum and Clean Around the Burned Area

If you have an upright vacuum, run it along the edges of the burn to clean up any loose dirt or debris that may have accumulated there. Then, using water and mild detergent solution, dampen a rag and wipe down the surrounding area. Make sure you do not use too much soap because it can make treating the carpet later.

Once you have cleaned up the area, let it dry. If the fibers around the burn are very thick, you may want to use a hairdryer to ensure the area is completely dry before proceeding. It is also a good idea to use fans because the moving air will help the carpet dry faster.

Step Three: Test the Stain Remover

Do not skip this step! If you are using a solution other than water and dish soap to treat the burn, it might be wise to test it on an area of the carpet that is not discolored. This is a way to ensure the product will not damage the floor in a different area of your home.

Using Water and Dish Soap Has Safe for Most Carpets.

If you use water and dish soap, you do not have to test it because this solution has been proven safe for most carpets. However, if the burn is particularly bad, you may have to use a commercial carpet cleaning product. Use the same process as before to test your solution, but wait at least 10 minutes before you proceed with treating the burn.

Step Four: Treat the Burn

A packet of unflavored gelatin will do wonders for burned carpets because it effectively removes color and odor from stains. To use it, pour about a quarter of a cup of gelatin into a microwave-safe bowl. Then, add about two cups of hot water to the mix until the powder is completely dissolved.

Stir in some dish soap and pour it all over the burn on your carpet. Let this mixture sit for about an hour, but periodically check to make sure the mixture is still wet. If it starts to dry out, add a little more water and stir in some dish soap again. Once the hour has passed, pour another quarter of a cup of hot water over the area and use your vacuum to suck up the mixture.

You Can Check It Out to Get Tattoo Ink Out of Carpet

Step Five: Sprinkle Baking Soda

When your carpet is dry, sprinkle a liberal amount of baking soda over the spot where you removed the burn. Then, use a brush to gently work the powder into the carpet’s fibers and leave it for several hours before you vacuum again. This process will help eliminate any remaining odor and discoloration that might be leftover from the burn.

Sprinkle Baking Soda

Then, use a carpet cleaning brush to work the baking soda into the fibers of the carpet. Let it sit for about five hours before you vacuum again. If there are still black marks on your carpet, repeat this step until they are gone completely. It may be necessary to lightly scrub dried areas with dish soap or another stain remover for stubborn spots that do not want to budge.

Step Six: Replace the Baseboards and Flooring.

Once your carpet is dry, you will want to replace any baseboards that were removed. Push them back into place so that they are flush with the walls and there are no gaps between them and the wall or each other. Finally, vacuum up any loose baking soda particles to get every last speck!

After your baseboards are in place, you will want to replace any flooring removed during this process. This could be carpet or ceramic tile, depending on the area of your home where the burn occurred. This will help in how to get straightener burns out of carpet.

Step Seven: Maintain Your Carpet

Once your carpet looks new again, you will want to take some steps to maintain it so that this does not happen again. First, reduce the amount of time you have your iron or straightener on. It might be impossible to avoid using them completely, but try to use them when you only have a few pieces of clothing that need to be straightened.

Maintain Your Carpet

You can also purchase iron board covers or lay down a paper towel over the area where you will be using your straightener before plugging it in. This will help reduce the temperature and make your carpet less likely to burn if you touch it by accident.

Frequently Asked Questions

Is Burning Carpet Toxic?

Carpet burning can be very toxic to your home, the air, and yourself. Carpet fires release a significant amount of toxic chemicals into the air. These chemicals include carbon monoxide, benzene, hydrogen cyanide, formaldehyde, and many others.

Some of these chemicals are carcinogenic and cause cancer in humans and animals alike. This is why carpet burning should be avoided as much as possible if you want to keep your family safe from harm.

Can Carpet Be Lightened?

Carpets can be lightened by using a professional carpet cleaner that has been designed for lightening carpets. You can also use a non-toxic shampoo to remove stains and dirt from the carpet, then rinse it with cold water before applying the cleaner.

Does Vinegar Ruin Carpet?

No. Vinegar does not ruin carpets because it does not damage fibers or cause discoloration in any way and leaves behind a fresh scent that many people find pleasant. Vinegar is a natural cleaner that can be used on many surfaces. If you have some type of stain on your carpet, you can use Vinegar to remove it.


When dealing with a straightener burn on your carpet, removing the scorching right away is essential. If you cannot do this yourself, call in professionals that can take care of it for you. It will be worth the investment because if left untreated, these burns will spread and could set fire to other areas of your home or office space.

The quicker action is taken after one has been made, the less damage there will be done overall. This information should help make sure that your carpets stay safe from any future accidents! We hope you enjoyed this article on how to get straightener burns out of carpet.

Check it out also – How to Get Transmission Fluid Out of Carpet.

Smart Home Pick