How to Hide Ethernet Cable Along Wall

With so many cables running along the walls in a home, it can be challenging to find a place to hide them. One way you can do this is with an Ethernet cable that easily plugs into your router and provides internet access for all of your devices. The best part is that it’s easy enough to run the cable behind molding or under baseboards if you want! 

While basic cable management will suffice for most people, some individuals might need more specific solutions. There are plenty of products on the market explicitly designed for hiding wires from view while also protecting them from potential damage due to wear and tear.

How to Hide Ethernet Cable Along Wall

For example, there are power strips with outlets hidden inside drawers, allowing users to close the drawer when not in use without unplugging anything. You need to know how to hide ethernet cable along wall.

Step to Follow on How to Hide Ethernet Cable Along Wall

Step One: Cut the Ethernet Cable

Cut off a single cable at about 8 inches long. This will be used to connect your wall jacks, so be sure it’s long enough to reach from one box to another when the boxes are mounted on the wall. Next, strip off about 1/2-inch to 3/4-inch of the cable’s outer jacket.

You can use a utility knife or wire strippers to do this, whichever you prefer. Be sure to keep the twisted pairs of wires intact. Keep in mind that this 8-inch piece of cable is only to be used for making connections between wall jacks. Do not run it from one end of your house to the other. You will need an additional piece of cable for that purpose.

Step Two: Connect Cable Between Boxes

Take the 8-inch piece of cable you just cut and strip off about 1/2-inch to 3/4-inch of the jacket. You will be connecting this piece of cable between two wall boxes, so try to keep the wires as neat as possible. Connect one end of the cable to a port on one of the wall boxes.

Wire Connected to the Box by Matching Colors

You will see a metal clip with six holes. The six wires from the cable should fit into any one of those six holes. Match up the colors as closely as possible and push the cable into place. It takes a bit of pressure, so do not be afraid. Once you’ve done this, cut off all but about 1/2-inch of the cable jacket.

Step Three: Prepare Ethernet Cable for Mounting

On one end of an additional Ethernet cable, strip off about 1/2-inch to 3/4-inch of the outer jacket. On the other end, you will find four color-coded twisted pairs of wires. Cut off all but about an inch or so of the outer jacket; this assumes you will be securing the cable to the wall with a cable raceway.

Keep the twisted pairs of wires intact and strip off about 1/2-inch to 3/4-inch of insulation. If the wire is solid copper, you may use a utility knife or wire strippers to do this. Strip off about 1/2-inch of insulation from each wire inside the four twisted pairs of the cable.

Step Four: Pull Cable Through Wall Using Fish Tape

Insert the end of your fish tape into your wall box. If you plan on running cable along baseboards, it’s a good idea to cut out an additional piece of drywall so the fish tape can be fed under the flooring. You may need to use brute force with this step.

Pull Cable Through Wall Using Fish Tape

Keep pulling with the fish tape until it squeezes through to your other wall box. Once this is done, pull out the 8-inch piece of cable you previously cut and hold onto one end. Be careful not to let go of this end, as you do not want to repeat these steps. Then, keeping a firm grip on one end of the cable, feed it into the wall box.

Step Five: Pull Out Cable From Fish Tape

Do not let go of the end of your fish tape until you have pulled all the slack out between where it comes out of one wall box and goes back into another. Then, insert this end back through your other wall box. You may now let go of the end you’ve been holding onto. 

Once again, be careful not to pull too hard, or you could pull your wall box right out of the wall. If you’re pulling the cable along baseboards, cut into your drywall to pull the rest of your fish tape through to the other side.

Step Six: Connect Wires to Wall Jacks

Take the wire you stripped off in Step Three and connect it to a port on one of your wall jacks. Please match up the color of the wire with its corresponding hole in the jack’s six-hole metal clip. Push this piece of the cable into place until it fits securely, then cut off all but about 1/2-inch of the cable jacket.

Connect Ethernet Cable From Wall Jacks

Take your other piece of cable and connect one end to a port on the wall jack closest to the location where you will be making in-wall connections to another room. Next, strip off about 1/2-inch of insulation from both ends and connect the cable to the wall jack in this room. This will help in how to hide ethernet cable along wall.

Step Seven: Make In-wall Connections

The trick here is to fish the cable through your walls to the next wall box without breaking too many tiles or plaster. You will need fish tape for this purpose, but if you are only running one cable, it might be easier to cut a hole in the wall. Take your fish tape, feed one end of it through the back of the wall box you are using for connections and push it out to where you will be running cable to another room.

On this side of the room, fish the fish tape under baseboards if at all possible. If you plan on running cable along baseboards, you may need to cut a small hole in your drywall so the fish tape can be fed under the flooring. Locate studs where possible and begin pulling out about 2-3 feet of cable from this point; careful not to pull too hard, or you could break tiles or plaster.

Conclusion

The best way to hide ethernet cables is by running them along the wall, just above the baseboard molding. It may take a little longer, but it will give you an aesthetically pleasing result that doesn’t look cluttered or messy.

If this seems too time-consuming for your taste, opt instead for tucking the cable behind furniture and curtains, so they are out of sight from guests who visit your office space regularly. We hope you enjoyed this article on how to hide ethernet cable along wall.

You may also like- How to Speed Up Your Internet Connection

Smart Home Pick
Logo