How to Install Laminate on Stairs With White Risers

Introduction

Laminate is one of the most popular flooring choices for modern homes. It’s affordable, durable, and provides a clean finish that looks like hardwood. But it can be challenging to install laminate on stairs with white risers because it requires cutting notches into the laminate to fit around tight corners. The good news is that installing laminate on stairs with white risers doesn’t have to be complicated or expensive—with these three tips, and you should be able to complete your project in one day! In this article, I will discuss how to install laminate on stairs with white risers. So let us get started.

How to Install Laminate on Stairs With White Risers

A Detailed Stepwsie Guide on How to Install Laminate on Stairs With White Risers

  1. Start by measuring the width of each riser, so you know how wide each piece of plywood needs to be cut. Remember also to measure from the edge of one stair tread up over the top of the riser. The plywood will not reach the backside of the riser, and Start by Measuring the Width of Each Riser and  So Know How Wide Each Piece of Plywood Needs to Be Cut ..
  2. Next, cut your plywood into pieces that are large enough to fit over each riser.
  3. Place a sheet of plywood on one side of a stair tread and line it up with the edge, so that overhanging piece from step 1 hangs down from it. 
  4. Nail or screw through the plywood into each stair tread using three screws for each piece approximately every 6 inches apart along its length. Be sure to use long enough screws so they go all the way through the treads and hit at least one riser beneath them(at least that is what I did, and it has worked well).
  5. Fit another sheet of plywood on the other side and nail or screw into each stair tread using three screws approximately every 6 inches. How wide should these pieces be? Well, they need to be as long as your riser’s width plus about 1/2 inch or so for trimming. If you cut them too short, as I did the first time, don’t worry, as you’ll have some exposed plywood edges, which is not a big deal. They can also be sanded down with a belt sander if necessary.
  6. Now that both sheets of plywood are nailed in place, go ahead and attach one edge to the front face of each riser.
  7. Use a jigsaw or circular saw to cut the front edge of each riser(the edge facing up the stairs) at an angle so that it meets with your already attached plywood pieces. If you do not cut the risers this way, when you install your next set of steps, they will not fit correctly against this one, plus there is no need to trim the backside. This also ensures that your outer stair treads are flush with these newly cut edges on each riser, so you don’t have any gaps between sets of stairs.
  8. Now that all of your riser faces are trimmed out in preparation for installing the step boards, go ahead and move on to cutting and nailing down those stairs themselves.
  9. Cut the stair treads to the proper length so that they fit in between your already nailed-down plywood sheets.
  10. Nail down each stair tread making sure there is a nail every 6 inches or so, driving through both the nail grooves and into the plywood underneath.
  11. Once all of your stairs are cut, trimmed, and nailed down, go ahead and remove each piece of plywood one at a time, leaving only the attached stairs behind.
  12. From here, you can apply flooring adhesive (I used Loctite PL Premium Construction Adhesive ) to the backside of each step board before installing it onto your stairs themselves. I left mine with their protective paper side facing up for about 24 hours.
  13. Once the adhesive has dried, you can finally install your laminate flooring on top of your stairs. I chose to work my way up with separate pieces, but some folks may decide to do it in long rows, so they don’t have to cut any boards(I did this on my latest installation and found that it is much more complex than working up each piece one at a time).
  14. Cut each board using a sharp utility knife, scoring the backside several times before pressing down firmly on both sides to snap it cleanly in half. Once all of your stair treads are cut down, go ahead and remove their protective sheathing.
  15.  Use spacers between each step when installing new stairs so that all of the pieces fit together nicely. Notice how my top stair board does not line up precisely with the risers on the other sets(this was because I chose to install it separately after cutting it down), which is just fine as long as there are no gaps between steps.
  16. That’s about all there is to it, folks! Once everything has been cut, nailed, and glued, you will have a nicely finished set of stairs at your disposal.

Precautions While Installing Laminate on Stairs With White Risers

Before starting to do the installation, you need to take some precautions. These are mentioned below:

Before Starting to Do the Installation and  Need to Take Some Precautions.

You must first check whether all the types of materials over which you want to install laminate are compatible with each other or not. You can also ask for a sample from the dealer if you are not sure. This will also help you in avoiding any future damages caused by incompatible materials. Generally, laminates come with a seven-year warranty, but they may vary according to the supplier and product model. So make sure to read its warranty policy before buying it. Also, see whether they have mentioned the proper precautions because if something goes wrong during installation, they will only be responsible for repairing or even replacing the product.

It would help if you prepared the substrates properly because it is one of the essential parts of the installation process. First, you will have to check if they are flat, smooth, and even otherwise, you might end up with damages, including cracks, deformities, warping, etc. After this, your next step should be leveling up all the materials, including floors, and then filling any gaps or holes due to nails or anywhere else that may create a problem during the installation process. This way, you can prevent future damages caused by uneven surfaces. Lastly, make sure to get rid of dust from there before starting with the task.

What Are The Benefits of Installing Laminates on Stairs

Installing laminate is an easy, affordable way to give your stairs a new look. Once installed, it will last for many years. A new laminate can completely transform the look of your staircase and make it look new again at a fraction of the cost of replacement or refinishing.

What Are The Drawbacks Of Installing Laminates on Stairs?

Although installing laminate flooring is simple enough for even non-skilled DIYers, you’ll need to consider whether you are prepared to do the job yourself. If you’re not comfortable with home improvement projects or working with tools, then hiring professional subcontractors might be more appropriate for your needs. Another drawback is that sanding down the existing stairs before installation will increase the amount of dust in your home, making it difficult to work if you have asthma or other respiratory issues.

Conclusion

I hope this article has been essential for learning how to install laminate on stairs with white risers. Ensure all the necessary precautions while following the process. Thank you and have a nice day!

Check it also – How to Install Hardwood Flooring Around Stair Railings .

Smart Home Pick
Logo