How to Make a Single Curtain Rod Into a Double

There are many ways to make a single curtain rod into a double, but they all have one thing in common: they require the rod to be cut down. If you don’t want to do that, there is another way! You can turn your current curtain rod into two rods with just some simple DIY skills. 

How to Make a Single Curtain Rod Into a Double

There are many steps involved in this project, so I will try to break it down for you. Let’s start by measuring the distance between your window and where you would like your curtains combined on either side of the window or door.

Once we know how wide our new curtain needs to be, we can move on to cutting our old pole down and making it look great! So, this article is for you. You will learn how to make a single curtain rod into a double with just one simple trick!

7 Steps to Follow on How to Make a Single Curtain Rod Into a Double

Step One: Determine

First of all, you have to determine whether or not your single curtain rod can be extended or if it needs to be replaced. If the rod is too long for one window and too short for another, you will need to replace it. If this is the case, make sure the rod you buy is the same length as your window width.

Determining a Single Curtain Rod Into a Double

If the rod is not too long for one window but too short for another, you will need to decide if attaching two curtain rods using a joining bracket is possible. Most rods are adjustable, so it may be possible, though some are not. If this is the case, you will have to replace your rod or find one that can be extended.

Either way, if you are making the rod longer, you will have to measure it in its current state, then follow that measurement when purchasing a new curtain rod. If you are attaching two curtain rods, most joining brackets can be adjusted, so both rods are not necessary to come from the same window treatment store.

Step Two: Mark

Once you know where the rods will be placed, you can measure and mark them on your wall. Measure for both curtain rods if they are not the same to ensure that they are even. Then make a small pencil mark where these marks meet up on your walls.

You need to do this on both sides of each window pane if you are making the rod longer and on both sides of both windows if you are attaching two rods. You may also want to mark the bottom of each rod so that you know where they should hang straight.

This is especially important if the curtain rods are being made longer. When you have finished marking, place your rod or rods against the wall to double-check that they meet up correctly and mark any extra spots that need to be marked. This will help in how to make a single curtain rod into a double.

Step Three: Create Anchor Points

Once you have double-checked your measurements and made sure everything is accurate, take a small nail and place it on one of the pencil marks you made for either end of the rod. For example, attaching two rods makes a small nail at the top and bottom of each window pane.

Then hang your rod or rods from it to check if they are even. You can also hang a weight from them to test their strength because putting pressure on a curtain rod can cause it to bend, especially if you have a heavy set of curtains. If the rod bends, it will have to be replaced.

Putting Pressure on a Curtain Rod

If everything looks good, remove the rod and put a small bit of adhesive on each nail where you placed them for your anchor points. Then place the bottom of each curtain rod over its corresponding nails to dry against the wall. It would help if you let this dry for several hours or overnight.

Step Four: Threading

Now that your anchor points are secure, you can begin threading your curtains onto the rod if they are not already on it. Again, make sure to include the curtain rings, so you do not have to take them off once you have threaded them on. If any curtain panels are more than one panel wide, you will need to tie them together with a small piece of string.

Knot the string on both sides so that it holds the curtains together securely. Then you can knot them again so that they are all hanging evenly. You should now have two even curtain rods if you are attaching two or have had to replace your single curtain rod.

They should both hang down to the ground evenly, so it is best not to have the bottom of your curtains touch the ground just yet. Next, you need to make a small hem at the bottom of each curtain panel. If you want to find out more about how to make a single curtain rod into a double, keep reading.

Anchor Points in Curtain Rod

Step Five: Hems

To make a proper hem begin by measuring one side of the curtain panel from top to bottom. Then take that measurement and add two inches to it. Next, use this number to mark two lines with your pencil on the inside of the curtain panel, making sure that they match up at the corner.

Then use your ruler and measure half an inch inward on each line that you just marked. You should then mark two more lines with your pencil, this time along the bottom of the curtain panel. Then fold your fabric over to meet what is now the middle line and pin it in place or hold it down by hand to make sure that it stays put.

Create hemlines on the bottom of the curtain panel with the help of your ruler to make sure that they are even. Then cut along these lines using your scissors to create two hems at the bottom of your curtain panel. Now you need to do this on both sides of each window pane if you are attaching two curtain rods or you need to replace your single curtain rod.

Step Six: Finishing Touches

Now that you have all your hems made, you need to hang up your curtain panels and thread them onto the rod. It is an excellent idea to do this step once the adhesive has dried on one side but before it has dried on the other so that you can make sure they are even.

Then take this measurement and subtract half an inch from it. This will be how deep your hem needs to be on both sides of your window panes, so make sure it is small enough not to show when you use your measuring tape to mark it.

Then you need to make another set of hems along the bottom of each curtain panel on the inside, using your ruler and scissors just like before. If you use the steps outlined above for how to make a single curtain rod into a double, you can do it yourself.

Step Seven: Hang Up

Now you are ready to hang everything together by threading the curtains onto their corresponding rings. You should make sure that both sides of your windowpane are even, adjusting them if needed. But once they are done, you need to tie any panels that may be more than one panel wide into place with a small piece of string.

Knot the pieces of string on both sides to ensure they are secure, then knot them again, so the curtain panels are even. You should now have two curtain rods if you are attaching two or have had to replace your single curtain rod. They should both hang down evenly, so it is best not to have the bottom of your curtains touching the ground.

You should make sure that the hems on both sides of your windowpane are even, adjusting them if needed. But once they are done, all you need to do is tie any panels that may be more than one panel wide into place with a small piece of string. Next, knot the pieces of string on both sides to ensure they are secure, then knot them again, so the curtain panels are even.

You can check it to Make Curtain Tie Backs With Beads .

Conclusion

There are several ways to do this. One way is to use insulation tape and cardboard on the side where you want it doubled up. You will need some help from an extra set of hands, so get someone over there with you who can hold the curtain while you work it out.

This method has two drawbacks firstly; your new double rod won’t be as strong as one made by professionals; secondly, if they ever fall because something tips them over, insulation tape doesn’t stick well enough for a long-term fix. We hope you enjoyed this article on how to make a single curtain rod into a double.

Check it out also – How to Remove Curtain Gliders.

Smart Home Pick
Logo