How to Make Ceiling Fan Light Brighter

Ceiling fans are a great way to keep your house cool during the summer. But what if you want your fanlight to be brighter than it is? With just a little bit of work, you can make this happen quickly and easily! The steps below will show you how. 

How to Make Ceiling Fan Light  Brighter

First, find the switch for the ceiling fan light fixture on or near the wall in an area where it’s easy to reach. Next, turn off the power to that circuit by flipping the breaker in your electrical panel or using a circuit tester. Third, remove any bulbs from their sockets with care, so they don’t break.

Fourth, use needle-nose pliers to twist off each wire connector one at a time until all wires are disconnected from its socket. Fifth, use a screwdriver to remove the screws that hold your lamp fixture in place. Finally, in this blog post, we will go over how to make ceiling fan light brighter.

Step to Follow on How to Make Ceiling Fan Light Brighter 

Step One: Use a Bright Light

The bedroom is meant for sleeping, so it must be dark, but the ceiling fan needs some light. So make sure you have a bright floor lamp or table lamp on while you sleep. You can also get special lamps with tiny bulbs which are quite bright. These kinds of lamps may run on batteries too.

Step Two: Replace the Bulb

The average ceiling fan light bulbs are about 40 watts; this is not enough to read by night. If you can’t get a dimmable bulb, try finding some brighter ones around 100 watts or more. This should be easy considering most people want more light nowadays. If you’re at home, replace the bulbs while you’re up on the ladder.

Step Three: Use a Two-Prong Switch

If your ceiling fan has a second set of wires in the cord, attach them to two separate two-prong switches. Once one switch is turned on, the other goes off; however, you can switch both on by turning one-off and then the other. You can buy these switches at an electrical store or online.

Step Three: Get a Ceiling Light Fixture

You could replace the entire light fixture, which is not as hard as it sounds. All you need to do is attach the new one and turn on the power for safety reasons. However, this will involve tearing out all of your ceiling fan wiring and putting in a new cord. So if it’s a new ceiling fan, you might as well replace the light with a brighter one.

Step Four: Use a Drill Gun

If all else fails, then go ahead and drill a hole in your kitchen or bedroom ceiling for a brand new chandelier – they’re kind of elegant. Just attach it to the hole and turn on the power. This should be a last resort because it requires a lot of work, and the expense may not be worth it for homeowners.

If you follow these steps, you should have a brighter ceiling fan light in no time. However, if the problem is with your dimmer, then this may not work for you. If all else fails, call an electrician to fix it up for you!

Step Five: Give it to an Electrician.

If you’ve done all of the above, but there’s still no difference, your best bet is to call an electrician. Then again, if this was something simple, someone should have told you so by now. An electrician will fix the problem, and they may even make the fan light brighter for you. They know what they’re doing, so let them work their magic!

Step Six:  Get a Dimmer

To dim or not to dim, that is the question. If you’d rather have a ceiling fan light but don’t want it too bright, you can get a dimmer switch from an electrician. This works by slowly draining power from the light as you turn down the knob. Switching on full power will make your light as bright as it was before.

These steps should help you make your ceiling fan light brighter; however, you may need something else to make it work properly. The problem may also be with the wiring and not the bulb or switch. If you follow these simple instructions and still can’t get it working right, don’t hesitate to call an electrician to fix it.

Step Seven: Try the Light Impressions Bulb

The Light Impressions bulb is different because it never gets hot. It’s made of coiled wire, which glows like an incandescent light bulb but never gets hot. Each one lasts up to thirty thousand hours, so they don’t need to be replaced that often. This saves you money in the long run.

It will cost about twenty dollars for a pack of two. This is one option you have to consider in making your ceiling fan light brighter. If all else fails, give it a try and see if it works for you! Thanks for reading about how to make ceiling fan light brighter.

How Bright Should a Ceiling Fan Light Be?

The average ceiling fan light is not as bright as a regular light bulb. To make the room brighter, you can string together several bulbs in parallel. The more bulbs there are added to the circuit, the brighter they become. A general rule for how much wattage to use is about  60 watts for every foot of hanging chain.

Be aware, however, that by stringing the light bulbs together, you are creating one wire circuit with a lot of electricity flowing through it and only one little switch to turn it off and on. This poses a safety hazard, especially if there is any chance of children or pets playing near the ceiling fan.

Conclusion

If you’re looking for a ceiling fan light that is dimmer than others, we recommend the Hunter Fan Company. They offer many different styles and colors, so it’s easy to find something that matches your home décor.

Some of their models also have an integrated LED nightlight with on/off capability in the remote control, which can be helpful if you need some extra lighting while trying to get around after dark! Finally, the conclusion paragraph is informative and provides information on how to make ceiling fan light brighter.

You may also read this – How to Reverse Exhaust Fan Rotation

Smart Home Pick
Logo