How to Put Sand in Gas Fireplace

There are many ways to get a fireplace going, but none is more comfortable than with sand. This is because the sand will keep the fire steady and make it easier to start your fires. One of the best things about using sand is that it doesn’t create smoke or ash like some other types of fuel can.

How to Seal Water Heater Vent Pipe

Another way that people use sand in their gas-powered fireplaces is when they need to put out an existing fire – sprinkle some on top and watch as it does all of the work for you! But, if you’re looking for one last tip before trying this yourself, remember not to fill up your entire fireplace with sand. So, this article is for you. You will learn how to put sand in gas fireplace with just one simple trick!  

Steps to Follow on How to Put Sand in Gas Fireplace 

Step One: Purchase an Appropriate Amount of Sand.

This step is significant because if you do not purchase the proper amount of sand for your fireplace, it will affect how well the fire burns. You can find out how many pounds or kilograms of sand your fireplace needs by checking your owner’s manual (if it is available) or calling an experienced technician to come to your home and check the sand levels.

Step Two: Remove the Old Sand From Your Fireplace

First, make sure to turn off all of your gas lines. Then, retrieve a metal scoop (such as a cookie scoop or large serving spoon) to remove the sand in your fireplace and put it in an appropriate container (sandbox or heavy-duty trash bag). If you have no old sand to pull out, it is safe to proceed.

Remove the Sand in Your Fireplace and Put It in an Appropriate Container

Step Three: Clean the Inside of Your Fireplace

You must be sure that your fireplace is clean so that there are no particles or other material in the way of the new sand and the flow of air (it needs to pass through relatively unobstructed to be functional). Then, use a vacuum cleaner or broom and dustpan to clear out the remaining old sand.

Step Four: Install the New Sand in Your Fireplace

Using that same scoop, put enough new sand into your fireplace until it is approximately one inch high (or 2.5 cm if you are in Canada) from the top of the fireplace. This may not be as much as you think, as it is better to err on the side of too little sand than too much (you could overfill your fireplace and make a mess if you do not use enough).

Step Five: Light Up Your Fire!

After adding the new sand to your fireplace, turn on those gas lines and ignite your fire! It would help if you had a more steady flame with the new sand. If you wish, you can perform another step before turning on the gas to make sure that your sand is flat. If your sand forms a peak in the center, it will be difficult for the air to reach the flame and affect its burn. You can do this by simply using your hands or any hard object but not sharp or dangerous to flatten the sand.

Check it out to learn to connect propane tank to gas fireplace 

Turn on Those Gas Lines and Ignite Your Fire!

Do I Need Sand in My Gas Fireplace?

A gas fireplace is an effortless and inexpensive way to add ambiance and warmth to your home. Some units may come with a screen that sits in the bottom of the fireplace, but they tend not to look as pretty or “finished” as units that have been professionally installed. So, we look at you, outdoor propane fire table!

The last thing most homeowners want to do is empty sand into their fireplace, which is why professional installation is desirable. But if you find yourself with a gas fireplace and no professional on the horizon, rest easy. We have a solution for you!

Can I Use Glass Rocks in My Gas Fireplace?

Yes. Additionally, you can use glass jewels or other glass decorative rocks in a gas fireplace. Glass rocks should not be used in a wood-burning fireplace because the heat may cause them to shatter and result in flying glass pieces.

Rocks usually aren’t necessary for a gas fireplace, but if you want some decorative rocks, use onyx or obsidian stones. Never use sand in a gas fireplace because the high temperatures will cause it to explode.

Frequently Asked Question

Is All Sand Fireproof?

No, sand is not fireproof. However, it can be used to put out a fire.

Sand can be used as an effective extinguishing agent for fires because it is porous and absorbent. It will soak up the water from the surrounding area and reduce the fuel in a fire by reducing the air supply.

Is Sand Good for A Fire Pit?

Sand is not good for a fire pit because it can easily become airborne and spread to other parts of the camp. It also can cause injury if someone gets too close to the fire.

Where Do You Put the Sand and Embers in A Gas Fireplace?

If you have a gas fireplace, there are three parts to it: the burner, the chimney, and the draft.

The burner is in the middle of the fireplace on top of a grate. The chimney is usually located near the top of your fireplace and connects to a vent that will lead out of your home or building. The draft is at one end of your fireplace opposite from where you light up with a match or lighter.

Burner Is in the Middle of the Fireplace

What Kind of Sand Do You Use in A Fireplace?

The most common types of sand are:

  1. Sandstone – Sandstone is a type of sedimentary rock that is formed from compressed sand grains and quartz.
  2. Crushed brick – This material is the crushed remains of burned clay or bricks, typically used in fireplaces to add a decorative finish to the firebox walls.
  3. Ceramic tile – This material is used in traditional hearths and fireplaces as well as modern ones, made from a combination of cement, clay, and other materials such as metallic oxides and sulfates.


The steps to put sand in the gas fireplace are simple. First, you need to purchase a bag of sand from your local hardware store or any other retailer that sells this product. Next, pour the sand into the container provided with your gas stove and then light it on fire for about 20 minutes until all the kinks have been smoothed out.

Finally, make sure to cool off before adding more wood chips or logs to overheat the flame! It’s also important to remember never to place an open cup of liquid near a lit burner because spills can cause fires too. This concludes our blog post on how to put sand in gas fireplace hope you found these tips helpful!

You may also like – How to make gas fireplace flame yellow

Smart Home Pick