When remodeling your bathroom, one of the last things on your list is removing the bathtub. However, it can be a little overwhelming when you finally get to this point and start looking for instructions. The process includes using a jackhammer to break up the concrete and then pouring out all of the water from inside before having workers use their strength to pry off the tub with crowbars.
This is not only time-consuming but also very messy as well as unsafe! However, with just some simple tools and supplies that most homeowners have in their possession already, anyone can remove a bathtub without damaging tiles or ruining other parts of their house. In this blog post, we will go over how to remove a bathtub without damaging tiles.
Step to Follow on How to Remove a Bathtub Without Damaging Tiles
Step One: Determine
First of all, you need to choose a bathtub based on how kind of tiles it has. Then, because different tiles require different ways to remove the bathtub without damaging the tile, if you have a concrete type or ceramic flooring with epoxy grouting, you can pick up your new tub and place it into the old space one was.
You can also use a saw and cut off the bottom of the bathtub, leaving it sitting on the floor for stability while you finish removing tile adhesive. But if you have ceramic tiles on the walls of your tub surround, you must plan to remove the tile before removing the bathtub.
If you decide to remove the tub first, the next step is to drain it. For this, all you need to do is unscrew any drains or valves that will allow water to flow out of the tub quickly. Then take off the faucet handles and give them a good scrubbing before replacing them on the new bathtub.
Step Two: Mark
After draining the tub, you will need to mark a level line to install the new bathtub. This is an excellent time to have a helper hold a level on the wall directly behind your proposed location for a new tub. The best way to preserve tiles when removing old bathtubs is to use an adhesive remover.
Apply the remover liberally with a putty knife or scraper to both the bottom of your tub and the wall behind it. Then, scrape the remover material from the two surfaces off with a flat blade screwdriver, being careful not to gouge into either surface with too much pressure.
If you have a lot of adhesive in this area, you may want to clean the surface with warm soapy water before adding more remover. The goal is to remove all the adhesives from both surfaces so they will bond properly when you are done removing the bathtub without damaging tiles.
Step Three: Cut Out
Once you have cleaned the surface, you can cut the adhesive with a utility knife or a circular saw. Of course, it would help if you kept going until you completely removed the old tub and tore all tiles out from around it. But if you’ve heard about Tile Assist Strips, they can save a lot of work on how to remove a bathtub without damaging tiles by helping you tear up the tile easier and for a better look.
Once you have removed the old tub, remove all excess materials from around it to put your new tub in place. The best way to do this is with a shop vacuum attached to a long hose. If you don’t have one of these available, pick up any leftovers and sweep them away.
If you find any of the old adhesive or grout on your walls after removing the bathtub, scrape it off with a flat-bladed screwdriver. Wait about one hour for the adhesive to soften before scraping it away.
Step Four: Remove Bathtub
Now you can grab your new tub and place it in the area where the old one used to be. Of course, the best way to do this is to drain the water from it first. You can use a hose or bucket and place its spout inside any drains before draining them completely.
Ensure that there is not too much water in the bottom of the tub, as you might end up getting the new tile wet and causing it to slide. You should be ready to make a mess, but it can prevent how to remove a bathtub without damaging tiles then do everything possible first.
Once you have drained what you need to, place your tub and level it using shims or pieces of your old bathtub. This is to prevent the new tub from tilting and causing uneven tile work in the future.
You Can Check It Out to Hide a Bathtub
Step Five: Maintain
Make sure you maintain your new bathtub properly. Use a mild cleanser and a soft brush to clean it. Hard scrubbing can cause scratching that will require buffing or refinishing the tub, both of which are more expensive than simply cleaning it properly.
When you are done, wipe down the tub with a dry cloth to ensure no moisture remains. If you have a glass tub, dust may collect on it. In this case, use a microfiber cloth to wipe it down instead of a dry one. If the tub faucet is leaking, you can fix this by tightening the nut on top with an adjustable wrench.
Frequently Asked Questions
Can a Bath Be Removed Without Damaging Tiles?
It is possible that a bath can be removed without damaging tiles. To do so, you would need to use an enzyme cleaner and warm water to loosen the adhesive before scrubbing with a cloth or sponge. Make sure not to let any of the enzymes reach the tiles as this could damage them further. If all goes well, you should be able to remove your bath in just a few minutes!
What Is the Easiest Way to Take Out a Bathtub?
If you’re looking for an easy way to take out a bathtub, then you should consider using a plunger. Plungers work by suctioning onto the surface of the bathtub and using the user’s body weight to push and pull the plunger. This method is relatively simple and can be done in just a few minutes.
What Can Help Me Get in and Out of the Bathtub?
There are a few common ways that people try to get in and out of the bathtub, but none of them are really ideal. One example is using a step stool. While this might work for short periods of time, it becomes increasingly difficult as the person gets taller or their balance deteriorates over time. Another approach is to use a towel rail or shower caddy. These devices can be helpful in getting someone into or out of the tub quickly, but they can also be hazardous if not used properly.
The best solution may actually be something that doesn’t exist yet! A device called an incline bathtub chair allows users to easily get into and out of the bathtub without having to lift their body weight with weaker joints by leaning against one side or another of the chair.
How Do You Transfer an Elderly Person to a Bathtub?
The best way to transfer an elderly person to a bathtub will vary depending on the individual’s size, health, and mobility. However, some general tips that may be helpful include:
1. Make sure the elderly person is properly clothed and restrained – If possible, avoid exposing the elderly person to cold or wet environments. This will help to protect them from potential injuries.
2. Assist the elderly person into a sitting or standing position – Once they are in a sitting or standing position, help them down into the bathtub as gently as possible. Be sure to monitor their safety at all times.
3. Move the elderly person slowly and carefully – Never force an elderly person into a bathtub if they do not want to go in. Move them slowly and carefully so that they do not experience any undue stress or discomfort.
4. Call for help if necessary – If the elderly person becomes injured or becomes uncooperative, call for help immediately. Do not try to handle any medical issues on your own!
Conclusion
You can remove a bathtub without damaging tiles by using the following steps. First, carefully disconnect all of the water and drain pipes from under the tub. Next, break up any adhesives on tile with a hammer and chisel or crowbar. Finally, use some scraper to eliminate glue residue left behind on your flooring while you move out the old fixture and surround material.
If you follow these instructions closely when removing your bathtub, you should have no trouble doing so without damaging tiles. However, if you would like to save yourself a lot of time and money, consider hiring a group of professionals to help you with the process.
You may also read it: How to Clean Bathroom Sink Overflow Drain
