How to Remove a Section of Vinyl Fence

With the right tools and a little elbow grease, you can easily remove vinyl fence sections to make way for new additions or repairs. The process is not complicated, but it does require some attention to detail so that the old team does not damage your property while being removed.

How to Remove a Section of Vinyl Fence

If you have never done this before, it might be a good idea to get someone who has experience removing vinyl fencing on hand if something goes wrong. The process of removing a section of vinyl fence is one that anyone can do if they are willing to take the time and effort required.

It doesn’t need special skills or equipment besides what most homeowners already possess: an ability to follow written instructions and handle essential tools such as screwdrivers and hammers. In this article, we’ll explore how to remove a section of vinyl fence.

Step to Follow on How to Remove a Section of Vinyl Fence

Step One: Determine

First, you must determine why the section of vinyl fence is to be removed. Vinyl fences are often used in yards for decorative purposes but can also provide security when combined with dog kennels or other barriers. A damaged or warped section may need to be replaced entirely if it cannot be repaired in any way.

Determine the Reason why to be removed

A section of fence can also be removed to decrease the size of a fence for maintenance or repair. Again, this can be done without eliminating pieces if desired but requires more work than simply removing the damaged section and replacing it with an entirely new part.

If you don’t like the way a specific section looks, and it does not need to be replaced or repaired in any way, you can opt to leave it out when replacing pieces. Then, if further replacement is necessary, remove the section again and replace it with a new part, as you desire.

Step Two: Remove Vinyl

Remove a section of vinyl fencing by finding the top and working your way down. You will need to go from left to right or from right to left, starting at either end of the fence line you wish to remove. Pull back the bottom pieces as much as possible and push out those above, working up to one side of the fence section.

This can be done with a flathead screwdriver, but care must be taken to do so without damaging the fence itself or any of the landscaping around it. The fencing should come up fairly quickly, but you can use a hammer or pry bar if necessary.

Once you have the bottom pieces pulled back enough to get a grip on them, pull them out and away from the fence line. This should allow you to remove a section of vinyl fencing fairly easily by removing it whole once all sides are clear. You can then replace the damaged or warped sections as desired.

Step Three: Replacing a Section

Replacing a section of vinyl fencing is done in much the same way as removing one. Find your starting point according to your original plan and continue removing top pieces, working up. If you are replacing an entire section, you will need to obliterate the old part, but if you are only replacing a smaller unit, only pull the top pieces back enough to get to the other pieces underneath.

Replacing the Section

Once removed, replace with new sections of vinyl fencing by pushing them into place and working your way down again. It should be much easier than removal was since all that has to happen is for the pieces to be pushed into place. You can use a hammer or other means if needed but do not need to remove the fence from the ground.

Once you have replaced all sides and replaced your old section of vinyl fencing, push your bottom pieces back in and make sure they are secure against the ground. If they are not, replace them if needed with new parts. All of this information will help you learn how to remove a section of vinyl fence.

Step Four: Check for Further Damage

Check the fence line for further damage after replacing both fencing sections if you can do so without further damaging them. If there is any visible damage, you must repair it before going any further. Also, check for missing fencing sections, replaced sections that are no longer secured, and areas where the fence has pulled away from the ground.

If there is damage you cannot see from the outside, such as inside a dog kennel or another barrier, check from the other side or remove to check if there is damage. Repair as needed once you have identified the problem, whether replacing a section or repairing the damage.

Once you have repaired all damage to your fence, check your landscaping around your vinyl fencing for any problems as well. Make sure plants are not growing through the fencing and that other plants do not need trimming or other care to keep them from causing further problems with your vinyl fencing over time.

Step Five: Maintenance

Maintenance is an ongoing process for vinyl fencing, so checking it periodically will help you keep your fence in good shape for a long time to come. Check the bottom of the fence every month or so and push it back into place as needed.

Check the Bottom of the Fence Every Month

You can use a regular screwdriver or putty knife for this, but be sure to check for any damage to the bottom of the fence beforehand. Also, check for areas where the ground shows through, which may be damaged or warped beyond repair.

You Can Check It Out to: Fix a Sagging Vinyl Fence Gate

Concluding

The best way to remove the vinyl railing is by using a reciprocating saw. You can also use an angle grinder, but it will take longer and not be as accurate. If you are removing only one section of the fence, then this post has given you all the information you need!

However, if you are removing several sections, you may need to remove the fence from the ground to do so. To do this, find your starting point according to your original plan and continue removing top pieces, working up.  The conclusion paragraph is informative and provides information on how to remove a section of vinyl fence.

You can also check it out: How to Fill Gap at Bottom of Fence

Smart Home Pick
Logo