How to Remove Bathtub Drain With Broken Cross Bars

The crossbar on your bathtub drain can become corroded and may break off, preventing the water from draining out of the tub. If you have a broken crossbar or one stuck in place, it’s time to get creative with how to remove a bathtub drain without damaging it.

How to Remove Bathtub Drain With Broken Cross Bars

There are several different ways to solve this problem, and we’re going to show you some of our favorites today! The first method we’ll look at is using an adjustable wrench along with some baking soda and vinegar. This will dissolve any corrosion keeping your drain from moving freely while also providing lubrication for removing the filter itself.

Then we’ll take a look at what happens when all else fails: having to replace your entire bathtub drain. Finally, we’ll show you how to remove the old drain and install a new one using some helpful tips for plumbing jobs around the house. Learn how to remove bathtub drain with broken cross bars with this blog post!

8 Steps to Follow on How to Remove Bathtub Drain With Broken Cross Bars

Step One: Determine

First, you need to determine whether your drain assemblies are broken or worn out. You can do this by turning off the faucet and plugging the tub’s overflow hole. Once you’ve done this, run water through the bathtub; if it builds up in the tub, then call a plumber to replace your assembly or sealant.

Determine Your Drain Assemblies Problem

If the water drains slowly, there may be mineral deposits or other obstructions in the tub’s drain assembly. If this is the case, you can try cleaning it by removing the drain cover and gently brushing around the bathtub’s rim with an old toothbrush. If you get tired of removing pesky blockages every month, you can get a new bathtub drain assembly.

These come in several different varieties, each of which will fit a specific kind of bathtub. If you decide to get a new tub drain, replace the entire assembly rather than just the rubber stopper. This way, your bathroom’s look won’t be affected by mismatched hardware, and it’ll also ensure that no leaks develop in the drain assembly.

Step Two: Mark

Once you have determined that your drain assembly is worn out or damaged, please take the necessary measures to remove it. If all of the screws are loose, you can unscrew them. However, this isn’t always an option if some of the screws are broken or missing.

When removing a stuck fitting from the drain assembly, first loosen its screws. Then, wrap the fitting in a towel to protect it from any potential damage caused by using brute force. Next, with another towel wrapped around the drain assembly, separate the fitting from the drain with a wrench or large channel screws.

After the fitting has been removed, clean out any debris accumulated around the drain outlet. If the drain cover is loose, you can use a wrench to tighten its bolts or replace it with a new one. You should take these same measures if the bolts are broken or missing to not loosen over time.

Step Three: Drill Bathtub Drain

Once you’ve removed the broken fittings from your drain assembly, wrap its outlet with painter’s tape to avoid scratching it while you drill. Next, use a 1/8-inch masonry bit and gently drill into the drain’s rubber stopper until it is completely cut away; clean out any debris that may be inside of the opening.

If the hole is too small for the new drain to fit through, you can use a nail or ice pick to make it larger; be sure to lubricate the drill before using it. If this isn’t an option either, you can take your old drain assembly with you when purchasing a new one so that you know which size of rubber stopper will fit.

Once you’ve cut and drilled your way through the stopper, go ahead and install the new drain assembly. If the drain fits loosely in its opening, try to tighten it with a wrench or bolts; if this doesn’t work, you can apply silicone sealant around the inside of the stopper. This will help in how to remove bathtub drain with broken cross bars.

Step Four: Use Hummer

To break the old drain fitting, you will need a hand drill and small drill bits. Start by drilling a hole at the end of the fitting that goes into the tub. Keep going until you’ve drilled through to the other side. You can then cut out around this entire circle with a utility knife to make it easier to remove from the tube.

Once the fitting is removed, you will be able to see a ring of sealant. Cut through this with a utility knife. Once it is cut away from the drain opening, you should easily pull it out with your hand. If this doesn’t work, you can go back with the drill and gently start removing the remainder of the sealant ring around the edge.

Once this is done, you will be ready to install your new drain assembly. Most of the new drain assemblies come with a rubber gasket inserted into the opening before you screw down your new drain. If this is not included, be sure to apply a thick bead of silicone sealant around the inside of the ring for a watertight seal.

Step Five: Remove Broken Cross Bars

When replacing a broken tub drain stopper, you may want to consider using a new drain assembly with crossbars. Crossbars not only add a decorative touch to your bathroom but also make it easier for users who rely on bathtubs to take showers.

Change Your Broken Cross Bars

Cross-bar are installed in the same way as regular drains and removed in the same way. They are secured to the drain assembly with short screws often hidden under its outer flange ring. If your cross bars are broken, here is what you’ll need to do.

Mask around all of your surfaces with masking tape. Next, use a flat-head screwdriver to lift up the flange and pry out the screws. Finally, use a tub drain remover wrench or channel locks to unscrew and remove the crossbars and old drain assembly altogether. These steps should help you in learning how to remove bathtub drain with broken cross bars.

Step Six: Clean Out Hole

Now, you can go ahead and install your new drain assembly. If the holes in your flange have become badly corroded, you should clean them out with a drill or wire brush. You should also use this opportunity to apply a bead of silicone sealant around the inside of the ring for a watertight seal.

If the hole in the flange is too small for your drain assembly, you can use a nail or ice pick to make it larger; be sure to lubricate the drill before using it. If this isn’t an option either, you can take your old drain assembly with you when purchasing a new one so that you know which size of rubber stopper will fit.

Once you’ve cut and drilled your way through the stopper, go ahead and install the new drain assembly. If the drain fits loosely in its opening, try to tighten it with a wrench or bolts; if this doesn’t work, you can apply silicone sealant around the inside of the stopper.

You can check it to Remove Bathtub Drain Cover Without Screws

Step Seven: Place New Drain

Now, you should go ahead and place the new drain assembly in your bathroom. Use a tub drain wrench or channel locks to hold it steady and screw in the crossbars and screws; the process will vary depending on your particular brand of the drain assembly.

Once everything is in place, fill up your bathtub with water to see if the drain works. If it does, try sealing any drive screw holes with silicone sealant. If the drain doesn’t work correctly, you can go back and tighten up the screws a bit more or apply some extra sealant around the stopper.

If the drain is still not working properly, you can replace the stopper with another one that will fit. However, if this issue persists, you may need to buy your sink to figure out why it isn’t working correctly. All of this information will help you learn how to remove bathtub drain with broken cross bars.

You Can Check It Out to Clean Bathfitters Bathtub

Step Eight: Maintain Your Drain

It is essential to keep your tub drain and drain pipe cleaner to ensure that it doesn’t clog or cause other problems. To do this, you can make a natural cleaning solution. First, mix one-fourth cup of baking soda with one-half cup vinegar and fill up the mixture in a glass spray bottle.

Clean Your Bathtub to Avoid Other Problems

Add some hot water to the mixture and fill up the spray bottle with just enough water to cover the baking soda. Shake well before each use, then shake again before spraying your drain. Spray generously over the drains and allow them to soak for a few minutes before scrubbing everything with a brush or sponge.

Conclusion

In conclusion, it is possible to remove a bathtub drain with broken crossbars. However, this should only be attempted by someone who knows what they are doing and has all the necessary tools on hand. If you do not feel comfortable performing this kind of work on your own, it may be best to hire a professional.

Remember always to use gloves, goggles, and mask when handling chemicals. This will ensure that you are not exposed to any dangerous substances or substances that may be harmful to you. The conclusion paragraph is informative and provides information on how to remove bathtub drain with broken cross bars.

You can also read it: How to Retrieve Jewelry From Bathroom Sink

Smart Home Pick
Logo