How to Reset Generac Generator After Oil Change

If you’ve changed the oil in your Generac generator, it’s important to reset the unit afterward. This will ensure optimal performance and prevent any damage that could be caused by running the generator without its recommended oil level.

How to Reset Generac Generator After Oil Change

Your Generac generator is a valuable piece of equipment that can provide backup power during an emergency. A weekly routine maintenance check will ensure that it is always in working order. One important step in this routine maintenance is to change the oil. Here we provide a guide on how to reset generac generator after oil change.

10 Reasons Why You Should Reset Generac Generator After Oil Change:

1. To Ensure Optimal Performance:

By resetting the generator after an oil change, you can ensure that it will perform at its best. This is especially important if you rely on the generator during an emergency. If you want to be sure that it will work when you need it, it’s important to keep up with the recommended maintenance.

2. To Prevent Damage:

If you don’t reset the generator after an oil change, there is a risk of damage being caused by running the unit without the proper amount of oil. You can avoid this damage and keep your unit in good working condition by resetting the generator.

3. To Extend the Life of the Generator:

You can extend its life by taking proper care of the generator and resetting it after an oil change. This will save you money in the long run and ensure that you always have a source of backup power. First, make sure that the oil is at the correct level. If it is too low, add oil until it reaches the full line on the dipstick.

If it is too high, remove the oil until it reaches the full line. It is also important to change the oil and filter regularly. Follow the manufacturer’s recommendations for how often to do this. For most generators, it is recommended to change the oil every 50 hours or once a year, whichever comes first.

4. To Avoid Costly Repairs:

If you neglect to reset the generator after an oil change, you may have to pay for costly repairs. However, you can avoid unnecessary repairs by taking proper care of the generator and resetting it after an oil change.

Extend the Life  Of the Generator

5. To Maintain Warranty Coverage:

If you have a warranty on your generator, it is important to reset the generator after each oil change to maintain coverage. Otherwise, you may void the warranty and have to pay for repairs out of pocket. To reset the generator, consult your owner’s manual for specific instructions.

In general, you will need to disconnect the power, drain the oil, change the oil filter, and then refill the oil before reconnecting the power and starting the generator.

6. To Decrease Emissions:

One of the benefits of resetting your generator after an oil change is that it can help to decrease emissions. This is good news for the environment and also helps to keep your generator running more efficiently. So if you want your generator to be as green as possible, make sure to reset it after each oil change.

7. Fewer Maintenance Issues:

If you don’t reset your generator after an oil change, you may start to experience more maintenance issues. This is because the old oil can begin to clog up the system and cause parts to wear out more quickly. You can avoid these issues and keep your unit in good working condition by resetting the generator.

8. Improved Fuel Efficiency:

If you want to save money on fuel, it’s important to reset your generator after each oil change. This is because the old oil can start to gum up the system and decrease fuel efficiency. Resetting the generator will help ensure that it is running at peak efficiency. So, if you’re looking to save money on fuel, be sure to reset your generator after each oil change.

9. To Be Prepared for an Emergency:

If you rely on your generator for backup power, it’s important to ensure that it is in good working condition. One way to do this is to reset the generator after every oil change.

This will help ensure that the generator can start and run properly in a power outage. If you see the “low oil pressure” or “check engine” light come on, reset the generator as soon as possible.

10. Improve the Fuel Economy:

Many people don’t know this, but you can improve the fuel economy of your car by resetting the generator. When you do an oil change, the engine light will stay on until you reset the generator.

You are telling the computer that the oil change has been completed, and it can now optimize the fuel mixture for the new oil. This results in better fuel economy and performance.

Your Generator for  Backup Power

Step by Step Guide: How to Reset Generac Generator After Oil Change

Step 1:  Locate the Oil Fill Cap.

Before you start resetting your generator, you’ll need to find the oil fill cap. This is usually located on the side of the engine. Make sure you have a clean rag or towel handy to wipe away any oil that may spill.

Step 2: Disconnect the Power.

Once you’ve located the oil fill cap, you’ll need to disconnect the power to the generator. This can be done by either flipping the switch to the “Off” position or by unplugging the unit from the power source. Again, check if any oil is leaking from the fill cap before proceeding to the next step.

Step 3: Unscrew the Oil Fill Cap.

Use a wrench or pliers to unscrew the oil fill cap from the engine. Be careful not to strip the threads. It will be difficult to screw the cap back on later if you do. Also, make sure you don’t lose the O-ring attached to the cap.

Step 4: Drain the Oil.

Once the oil fill cap is removed, allow the oil to drain into a clean container. To do this, you’ll need to remove the oil drain plug. This is usually located at the bottom of the engine. Once the plug is removed, the oil will start to drain out. It’s important to use a clean container to reuse the oil later. Be sure to dispose of the used oil properly according to local laws and regulations.

Step 5: Clean the Oil Drain Plug.

Before you put the oil drain plug back in, it’s important to clean it off. This will help ensure a tight seal and prevent oil from leaking out. Use a clean rag or paper towel to wipe away any dirt or grime on the plug.

Clean the Oil Drain Plug

Step 6: Fill the Generator with Oil.

Once the oil drain plug is clean, you can start to fill the generator with oil. Be sure to use the type of oil specified in the owner’s manual. You can always check with your local dealer or service center if you’re not sure. Once the generator is full, screw the oil fill cap back on.

Step 7: Replace the Oil Filter.

After the oil has finished draining and you’ve filled the generator with fresh oil, it’s time to replace the oil filter. The oil filter is located next to the oil fill cap and is usually easy to spot. To remove the old filter, simply unscrew it by hand. Be careful not to touch the dirty filter or get any dirt in the housing. Once the old filter is removed, screw the new one on by hand.

Step 8: Reconnect the Power.

Once you’ve replaced the oil filter and filled the generator with fresh oil, you can now reconnect the power. Flip the switch to the “On” position or plug the unit back into the power source.

Step 9: Start the Generator.

After the power is reconnected, you can now start the generator. Be sure to follow the manufacturer’s instructions on how to do this. Once the generator is started, let it run for a few minutes to ensure that everything is working properly.

Step 10: Check the Oil Level.

Once the generator is running, it’s important to check the oil level. This can be done by looking at the dipstick or checking the oil level indicator (if your generator has one). If the oil level is low, you’ll need to add more oil. Again, be sure to use the type of oil specified in the owner’s manual.

Shut Down the Generator in Garator

Step 11: Shut down the Generator.

Once you’ve checked the oil level and everything looks good, you can now shut down the generator. Again, be sure to follow the manufacturer’s instructions on how to do this. Once the generator is shut down, you can now put away your tools and clean up any oil that may have spilled.

Final Thoughts

After completing an oil change on your Generac generator, it is important to reset the unit before restarting it. This will ensure that the generator runs properly and does not experience any problems.

There are many ways to reset a Generac generator. The process for resetting a Generac generator can be simple or complex, depending on the model of generator you have. 

The most important thing to remember when resetting your Generac generator is to follow the instructions in your owner’s manual. If you do not have your owner’s manual, you can usually find a copy online.

Once you have located the appropriate manual, follow the instructions that are mentioned in this blog post. We hope this blog post on how to reset generac generator after oil change, helps you the next time you need to reset your generator!

You can check it out to Use a Generator in an Apartment

Smart Home Pick
Logo