How to Restain a Deck That Is Peeling

If you want to know how to restain a deck that is peeling, this blog post will show you the steps. Many homeowners have proved that it can be difficult to find a way to get rid of all the old paint on your deck, but some tricks and tips can help with this process. 

It would help if you started by using a wire brush on areas where the paint is flaking off in large chunks. This will allow for easier removal of these areas later on when sanding down the surface of your deck.

How to Restain a Deck That Is Peeling

You also need to use a power washer on your deck’s surface before sanding down any loose or flaky paint from this area because it will make sanding much easier and more efficient.

7 Steps to Follow on How to Restain a Deck That Is Peeling

Step One: Get Out the Sandpaper

Before you can begin staining your deck, you have to remove any peeling or flaking paint. Unless it is a light-colored deck, the chances are good that there will be a considerable amount of loose paint when you scrape your deck. To remove this loose paint, get out your sandpaper and go at it.

If you have a belt sander, it should make the job go faster. Next, sand over the entire surface of your deck, going with the grain. The key to this job is persistence; keep at it until you have removed all of the flaking paint and smooth out the surface as much as possible.

Step Two: Clean the Deck

After you have sanded your deck, it is time to give it a good cleaning. Most cleaners can be purchased at home improvement stores. The basic idea behind any deck cleaner is that it will remove all the dirt and grime that builds up on a deck over time, prepare a clean surface for staining, and kill any organisms that might be living in the wood mold mildew, algae.

Cleaning the Deck Area Before Stain

The best thing to do is follow the directions of your particular cleaner. For example, some require you use their full strength, while others call for diluting with water. Additionally, some cleaners recommend letting the solution sit for a while before rinsing it off, whereas others immediately need to be rinsed off after application.

Step Three: Inspect the Wood for Problems

Once you have cleaned your deck, it is time to go over it one more time with a fine-toothed comb. Scrutinize every board to make sure that everything went well during your cleaning. Make sure there are no stains or dirt marks left on the deck.

If you find any mildew stains, there is a good chance that they will reappear once you have stained your deck. You can either use bleach or methylene chloride to remove these stains, but be sure to check with your local hardware store for instructions first. Also, always follow your cleaner’s instructions to ensure that you don’t do any damage to your deck.

Step Four: Make Sure the Wood Is Dry

After cleaning your deck and removing any mildew or mold stains, it will need to dry. Depending on the humidity of the area you live in, this might take anywhere from a couple of hours to several days. You can speed up this process with fans or heaters, but be very careful not to overdo it.

If the wood is too hot, you could do serious damage to your deck by causing splits or warping. If the wood freezes, it will expand and cause cracks. This is why it is important to let the deck dry at a natural rate. If you make it dry too quickly, it could ruin your deck.

Step Five: Choose the Right Stain for Your Deck

Once your deck is completely dry, you will be ready to choose what color you want to stain your wood. There are many shades available, so do some research to find the one that works best with your house style and taste. Once you have chosen a finish, buy an oil-based stain and a sealer.

 Choose What Color You Want to Stain Your Wood

Try to avoid water-based stains because they require too many coats that can be difficult to apply evenly. Oil-based stains dry faster and provide better coverage, which means less work on your end. These are usually sold in quarts, but you can find them in spray cans too.

Step Six: Apply the Stain to Your Deck

Before you start to stain your deck, make sure that you wear a breathing mask and old clothing. Oil-based stains create fumes and may also cause skin irritation. Also, make sure the area is well-ventilated because oil-based stains are very strong smelling.

To apply your stain, get an old towel and fold it in half. Dip one side into the paint tray containing the oil-based stain then wipe it onto your deck. Try to cover every board equally, or you’ll end up with a patchy look. Wait 10 minutes before applying another coat to avoid streaking. This will help in how to restain a deck that is peeling.

Step Seven: Clean Up Your Mess

Once you have finished staining your deck, make sure to follow up with a thorough cleaning. After all, you don’t want oil-based stains in the rest of your house! First, sweep up any drips or spills, then wipe down each board with a wet rag. Make sure to also clean the stain off of any tools you may have used during the process.

Clean Up Your Deck

That’s all there is to it! If your deck was peeling before, you should notice a big difference after staining. However, if you have followed these steps and the top layer of wood is still causing problems, now might be a good time for a new coat of paint or sealer.

You Can Check It Out to Refinish a Deck That Has Been Painted

Frequently Asked Questions

Can You Stain Over Peeling Stain?

Yes, you can. The first step is to clean the surface of the item before staining it. Make sure that you remove any loose particles from the surface and rinse it with warm water to get rid of any soap residue. You should also use a lint-free cloth to wipe down the surface so there are no particles on it that could interfere with your stain application.

After cleaning, apply the stain in one or two coats using a brush for best results and let dry completely before applying topcoat if desired.

Why Is Stain Peeling Off My Deck?

There are many reasons why your deck may be peeling. One of the most common reasons is due to extreme weather conditions like wind, rain, and sun. Another reason could be that the wood is not properly seasoned and needs to be soaked in water for a few days before it can also cure; if there are too many nails on the deck which can cause it to split over time because they increase friction with the wood fibers.

Do You Have to Remove Old Stain Before Restaining?

It is best to remove the old stain before restaining. The reason for this is that removing the old stain will ensure that the new paint sticks properly and also ensures that the surface does not become uneven, bumpy, or too glossy.

Can You Pressure Wash Stain Off a Deck?

Yes, it is possible to pressure wash a deck and remove the stain.

The process of pressure washing a deck will require some steps in order to get the best results.

Step 1: Use mild detergent and water mixture on the stain before applying more detergent or soap on top of it.

Step 2: Apply water over the area using a high-pressure hose to rinse off all excess detergent/soap mixture that has been applied onto the surface of the wood.

Step 3: Apply a cleaning solution (diluted bleach) with water in order to disinfect any bacteria or fungus that may have grown on top of the stain since it was first applied onto your deck.

What Deck Stain Will Not Peel?

Some deck stains will not peel, but some may. When Choosing a Stain That Won’t Peel, You Should Consider the Following :

  • The type of wood being stained.
  • The type of finish to be applied after staining.
  • How much pressure is applied during application.
  • The environment where the stain will be used and how well it adheres to natural and synthetic materials.

Conclusion

If you’ve found that your deck is peeling, there are a few steps to follow. First, clean the deck’s surface with water and dish soap or any other household cleaner that does not contain chlorine bleach. Next, apply an appropriate sealant as directed by manufacturer instructions for use on pressure-treated wood before rain or excessive moisture from snowfall can damage it again.

Finally, coat all surfaces with paint in color similar to the original finish, so no one will notice where it has peeled! The conclusion paragraph is informative and provides information on how to restain a deck that is peeling.

check it out to learn- How to Clean a Wood Deck Without a Pressure Washer

Smart Home Pick
Logo