The table fan has long served as an essential appliance, providing relief from the summer heat. Unfortunately, the fan’s blades are typically made of metal that can become rusted and corroded over time due to exposure to outdoor elements like rain and snow.
This rusting can cause damage to your tabletop or floor if it’s not tended to quickly. You must take care of this issue before it worsens and starts damaging other parts of your home.
If you want some tips on how best to lubricate a table fan, keep reading! So, this article is for you. You will learn how to lubricate a table fan with just one simple trick!
10 Steps to Follow on How to Lubricate a Table Fan
Step One: Remove the Blade.
Unplug your table fan completely. Take a screwdriver to your table fan’s screws, and take them all out so you can remove the blades without removing anything else. The outer cover will come off with the blades still attached. Use caution when removing these parts, so no one gets hurt by being pinched!
Step Two: Find The Bearing
Once you’ve removed the outer cover, look at the center of the blade assembly. You’ll see a circular metal part called the spinner. Find the bearings on all sides of it and make sure they are spinning freely. If any of them seem to be acting funny, use a small drop of oil to lubricate them until they work correctly again.
Step Three: Apply Oil
Apply a few drops of machine oil or 3-IN-ONE oil to the spinner and bearings. Using a paper towel, wipe away any excess that will not soak into the parts. Make sure you don’t overdo it on the oil because just a little bit is all that’s needed for lubrication purposes!
Step Four: Reassemble and Test
Replace the outer cover and blades onto your fan and plug it in. Make sure you observe how the bearings work, and if they’re still working smoothly, then you’ve done a fantastic job! If they seem to stick or not spin as well as before lubrication, go ahead and use more oil to lubricate them once more.
Step Five: Maintain Lubrication
If you think your bearings may need a little extra care, it’s okay to use this same process about twice every year or so. It depends on how often you use your fan and if you notice any squeaking sounds or anything like that. If you do need to lubricate more often, keep an eye on your bearings so you can catch any problems before they get worse.
Step Six: Avoid Disassembly
If you’ve tried these steps and the bearings are still squeaking or not spinning smoothly, it’s best not to disassemble your table fan. Many parts will require tools that are not easy to use, and they will most likely make your problem even worse. So instead of risking it, call a repairer in your area to come to fix the fan for you!
Step Seven: Check for Loose Parts
Sometimes, squeaking sounds can come from the motor housing. If anything is loose or rattling inside your fan, it may be best to tighten everything up first before you do lubrication. This way, you don’t have to worry about oiling up loose parts that are just going to continue making noise later on down the road.
Step Eight: Oil the Blade Assemblies
Take a paper towel and use a few drops of 3-IN-ONE oil. You can apply this to your blade assemblies the same way you did with the bearings. Make sure, though, that you aren’t getting any on any metal contact points or anything else that is not intended to have oil on it.
Step Nine: Oil the Motor Housing
Use a paper towel and some 3-IN-ONE oil for this final step. It’s best to put a few drops onto your hand and rub it across the housing rather than dousing the entire thing with the oil. This way, you’ll distribute it evenly and not cause problems later on down the road. Thanks for reading about how to lubricate a table fan.
Step Ten: Test and Reassemble
Plug your table fan back in and make sure it runs smoothly. If you hear a noise or anything out of the ordinary, stop using it immediately and find what is making the sound. Most likely, it’s a loose part that needs to be tightened or something similar if the fan runs smoothly; congratulations! You are now done with your lubrication job, and it’s time to enjoy your table fan all over again.
Can You Lubricate a Bathroom Fan
If you find that your bathroom fan is not working as well as it should, here are some steps you can take to try and fix the problem. Depending on the issue, you may solve the problem yourself by lubricating or replacing parts of the fan.
Lubricating the motor is a particularly straightforward job. You generally unscrew a panel on the fan’s casing to reach the blades and motor, which you can lubricate with a little machine oil. Be sure not to get any oil on the electrical components of your fan. Replacing the belt that turns the blades may also fix issues with your bathroom fan.
A faulty switch or power cord may also be responsible for your bathroom fan problems. While the initial cost of these parts to repair your fan may be greater than lubricating it, they could solve other problems down the road and save you money in the long run.
Frequently Asked Question
Can You Use Motor Oil for a Fan?
No, you cannot use motor oil for a fan. Motor oil is a type of petroleum-based lubricant that is used to keep parts moving smoothly within the engine of an automobile. It should not be used in any other application where it will come into contact with food or anything else you would want to consume.
Which Oil Is Best for Fan Motor?
The most common type of oil used in fan motors is a semi-synthetic, mineral-based oil. These oils are made from crude petroleum and refined using solvents and catalysts such as hydrogen chloride, sulfuric acid, or alumina.
The most popular synthetic motor oils for high performance engines are those that contain esters (e.g., amyl) rather than straight olefins (e.g., mineral).
Mentioned below are some of the benefits of these oils:
- Synthetic oils resist oxidation better than mineral based ones due to their higher level of antioxidant content.
- They can be formulated with low friction additives such as zinc dithiophosphate, calcium stearate, or graphite which make them more resistant to wear and sludge build up during long periods at high speeds under load conditions.
- They offer excellent corrosion protection against water and other contaminants like sulphuric acid and oxygenates like ethanol or methanol which could damage bearings over time without any oil sealant being needed for protection against leaks.
Conclusion
The last thing you want to do is make a mess by spraying oil all over the place. Instead, use an old toothbrush or other clean, lint-free material and apply the lubricant sparingly as you work your way around the blades.
If it’s been a while since your fan was last serviced, remember that its blade surface may be corroded from grease build-up, so don’t skimp on applying plenty of fresh lubricants to get everything running smoothly again.
Once done with this step, turn on the power switch and let any excess liquid evaporate before adding power back to both screws at once for maximum efficiency! In the end, we also offer some practical tips on how to lubricate a table fan.
You may read also – How to Oil Vintage Fan
